Roll over image to zoom in
Business managed Switch S3000-8TP2S
8*10/100/1000 Base-T ports(POE/POE+)
2* 1000 Base-X SFP ports
IEEE 802.3af/at
Total Output Power:150W.
Gigabit L2 Managed POE Switch
Product Features:
- Provide -48V DC power for powered devices (PDs), such as IP Phones, WLAN APs, and Bluetooth APs.
- Compatible with both IEEE802.3at(30W) and IEEE802.3af(15.4W), can supply power to PDs under these two standards.
- Automatically detect and supply power to IEEE802.3at and IEEE 802.3af compliant powered devices(PDs).
- Only supply power to IEEE 802.3af/at compliant PDs, no worry about damaging other private standard PoE devices or devices without PoE function.
- Support port power supply prioritization, guarantee the continuous power supply of key nodes.
- Up to 100m network cable transmitting distance, support flexible network expansion without power line deployment concerns. Users can freely fix their wireless APs, IP cameras or other end devices on the wall or ceiling.
- Support short-circuit protection function, the switch will automatically start short-circuit function and cut off the power supply when there are high-current or other power failures, which can efficiently defend against device damage or network failures caused by line fault or wrong installation.
- POE intelligent strategy: POE intelligent diagnosis, POE timing restart, Power supply schedule.
- Support CLI Management ,SNMP Management, simple WEB management, easy to configure the functions of switches.
Description
Product Description:
S3000-P Series is a smart PoE switch independently designed by the company. Featured with 8/16/24 IEEE 802.3at/af-compliant RJ45 ports, it supplies a maximum PoE power output of 120W/220W/370W. The switch can supply power when transmitting data with APs, IP cameras, and IP phones through CAT5 cables . Featured smart management functions, POE intelligent detection, 802.1Q VLAN, link aggregation, QoS and MAC address binding, it minimizes the difficulty and cost in networking deployment.
Product Specifications (POE):
| Product Features | Product Model : S3000-8TP2S |
|---|---|
| Hardware Specifications: | |
| Fixed Ports | 8*10/100/1000 Base-T ports(POE/POE+) 2* 1000 Base-X SFP ports |
| Consloe | 1 |
| Reset | 1 |
| Max Output Power(single port) | 30W |
| Total Power Consumption | 150W |
| PoE Pin-out | 1/2(+),3/6(-) |
| Switching capacity | 20Gbps |
| Forwarding Rate | 15Mpps |
| Flash/RAM | 16MB/128MB |
| Temperature | Operating temperature: (-10 - 50)°C Storage temperature: (-40 - 70)°C |
| Humidity | Operating humidity: (10% - 90%) RH, non-condensing Storage humidity: (5% - 90%) % RH, non-condensing |
| Dimensions(L*W*H) | 280(L)*180(W)*44(H)mm |
| Power | AC:100～240VAC,50～60Hz |
| Power consumption | 150W output the whole device |
| Weight | <2.5Kg |
| Lightning protection | 6KV |
| MAC address table | 8K |
| LED Indicator | Power, Link/Act, POE |
| Software Specifications: | |
| Forwarding mode | Store-and-forward |
| MAC Address | Static configuration and dynamic MAC learning MAC browsing and removal Configurable aging time of the MAC address |
| Jumbo frame | 12K |
| Port Characteristics | Support outbound and inbound port speed limit Support outbound and inbound port speed limit IEEE 802.3x traffic control for Full-Duplex mode Back-pressure traffic control for Half-Duplex mode Storm suppression for unknown Unicast, multicast, multicast, broadcast type Storm suppression based on bandwidth regulation and storm filtering |
| Port Aggregation | Support port aggregation Support static aggregation Support dynamic aggregation(LACP) Support source MAC payload Support destination MAC payload Support based on source and destination MAC load Support load based on IP address |
| VLAN | 4K support VLAN Port-based VLAN MAC-based VLAN Protocol-based VLAN VLAN based on IP subnet Voice VLAN 802.1ad(QinQ) |
| Layer 2 Ring Network Protocol | 802.1d STP, 802.1w RSTP, 802.1s MSTP Port Fast, Uplink Fast, Backbone Fast BPDU Guard, BPDU Filter, Root Guard Standard ERPS ERPS single ring single instance ERPS single-ring multiple instances Support multi-ring ERPS |
| IPv6 | IPv6-Ping ,IPv6-Telnet,IPv6-TFTP,IPv6-ICMP |
| Multicast | IGMP V1/2(Snooping) |
| DHCP | DHCP Client DHCP Snooping |
| Mirror | Support port mirroring for incoming port packets Support port mirroring for outgoing port packets Support port mirroring for inbound and outbound packets Support multi-to-one destination port mirroring Support CPU mirroring |
| ACL/QoS | Access list based on source mac Mac access list based on ethertype Ip access list-standard ACL Whether to support the access list of the time period ACL verification of source IP address ACL verification of the destination IP address ACL verification of source port ACL verification of the destination port Support 802.1P (CoS) priority marking Support Qos based on COS Support 8 queues Support SP, WRR, SP+WRR and other scheduling modes |
| Safety Features | Support port-based 802.1X local authentication Support 802.1X remote authentication Support port-based MAC address filtering Authentication based on MAC address Support Radius authentication Loop detection (private) Support port isolation Single port isolation Multiple groups of port isolation Port security ARP Aing/Bnding Support storm suppression for multicast/unknown unicast/broadcast |
| Energy saving | IEEE 802.3az |
| Management and Maintenance | CLI: Console, Telnet, SSHv1/2 Web-GUI: HTTP, HTTPS SNMPv1/v2 SNMP Alarm/Inform/Traps RMON Support RMON(Remote Monitoring)Alarms, Events, History (*) Support LLDP NTP v1/2 System log (operation log, alarm log) Syslog support Support user hierarchical management and password protection Support restore to factory mode Debugging |
| POE | Support 802.11af/at Power Supply Power and data at the same time Power supply pin 1/2(+), 3/6(-) POE intelligent diagnosis POE timing restart Single port output maximum power 30W Power priority setting |
Reviews
There are no reviews yet.